sintering temperature

Based on the analyses of the principle of the microwave sintering, the microwave sintering system is been developed. The system is made of personal computer, infrared thermometer, temperature controlling device, and the microwave cave.

本文在微波烧结原理分析的基础上，利用计算机、红外测温仪、智能温控仪和微波反应腔等设计出了PTC陶瓷的微波烧结系统。

Improving body briquetting pressure could promote densification of nanometer-level aluminum nitride, but such influence gradually became weak with improvement of sintering temperature.

提高坯体成型压力可以促进纳米级氮化铝烧结致密化，但此影响伴随烧结温度的提高而逐渐微弱。

Firstly the influence of sintering temperature and ball milling time on the electrical properties, density or undoped Y_2O_3 ZnO-based varistor were researched.

首先研究了高能球磨制备未掺杂Y2O3氧化锌压敏电阻的工艺条件和电特性，筛选和优化了球磨时间参数和烧结工艺。

The mechanism of low temperature sintering is discussed by means of TG, DTA and DDTA, and the optimum sintering temperature range is between 850~ 900 ℃.

利用TG、DTA、DDTA等分析手段研究Bi2O3的低温烧结机理，并确定最佳烧结温度范围在840～900℃之间。

The effects of composition and sintering temperature on the microstructure and properties of the Titanium-Based Composites were investigated by X-ray diffraction, optical microscope, scanning electron microscopy and mechanical properties tests.

我们通过X射线衍射分析、金相显微镜、扫描电子显微镜和机械性能测试研究了成分组成和烧结温度对钛基复合材料机械性能和生物相容性的影响。

Study of the Relation Between Electromagnetic Parameter and Sintering Temperature of Low Loss Mn-Zn Ferrite

低损耗Mn-Zn铁氧体电磁参数与烧结温度的关系研究

Relation between Sintering Temperature of Cathode Blocks and Versus Oxygen Concentration in Electrolytic Tantalum Powders

阴极块烧结温度与电解钽粉氧含量的关系放电等离子烧结制备铁基大块非晶材料

This paper introduces the study and test work of the low-temperature sintering of magnetite concentrate with addition of Hamersley fine ore.

本文介绍了使用磁铁精矿配加部分哈姆斯利矿粉（哈粉）的低温烧结试验研究工作。

The optimum preparation condition was that sintering temperature was 1215 ℃ and holding time was 45 min.

磁体的最佳烧结条件为：温度1215℃，保温45min。

The favorite conditions of preparing oxygen cathodes are that the mass ratio of graphite: acetylene black: activated carbon is 1 ∶ 1 ∶ 1, the sintering temperature of the cathode is 400 ℃ and the thickness of the cathode is 1 mm.

电极的较佳制备条件为：石墨、乙炔黑与活性炭的质量比1∶1∶1，烧结温度400℃，电极厚度1.0mm；

The methods to modify the volatility amount of organic vehicle were proposed, and the volatility data are useful for the reference of the sintering temperature schedule of electronic paste.

提出了调节有机载体在不同温度下挥发量的方法，可为电子浆料烧成温度制度提供参考。

Sintering temperature has also great influences on fracture characteristic and properties.

烧结温度对断口形貌和力学性能也有较大影响.

The density of sintered pellets increases with the sintering temperature at constant sintering time and the increment of the sintered-pellet density with the sintering temperature is much more significant than that with sintering time.

在相同的烧结时间内，提高烧结温度，烧结块的密度随之提高，且提高程度比延长烧结时间提高的程度更为显著。

Porous silica ceramics with low density were successfully fabricated by a novel tert-butyl alcohol ( TBA)-based gel-casting method. The effects of solid loading and sintering temperature on the microstructure, phase, pore size distribution and physical performance were studied.

研究了不同固相含量和烧结温度对制备二氧化硅陶瓷显微结构、性能、物相以及孔径分布等方面的影响。

The Influence of Sintering Temperature in NiO Target on the Properties of Exchange Coupling NiO/ Ni_ ( 81) Fe_ ( 19) Double Layered Films

NiO靶烧结温度对NiO/Ni（81）Fe（19）双层膜的影响

The compression strength and osmotic coefficient of the permeable bricks were antinomies relation, which were affected by shaping pressure sintering temperature aggregate size.

粉煤灰透水砖的抗压强度和透水系数是一对矛盾关系，主要受成型压力、烧成制度、骨料粒径等因素影响。

The paper introduces the research and manufacture of P/ M cylinder cover for compressing machine with focus on the influences of density, sintering temperature and aqueous vapor treatment on the tensile strength.

介绍了粉末冶金压缩机缸盖的研制过程。重点讨论了密度、烧结温度以及蒸气处理对抗拉强度的影响。

The comparison shows that the thermal etching carried out at a temperature lower than the sintering temperature can obviously reveal the grain structure of Al_2O_3 matrix. The metallic particles after thermal etching were not moved away from the samples, as normally occurred in chemical etching.

比较表明，在低于烧结温度约150℃下进行的热腐蚀能够清晰地揭示基质Al2O3的晶粒结构，并且与化学的效果不同，保留了金属相粒子。

The experiment results indicated that the complete perovskite structure is obtained when the sintering temperature is about 1200 ℃ of the PCZ ( 0.33) ceramic prepared by solid oxide.

实验发现，用固相法制备的PCZ（0.33）的陶瓷在1200℃左右烧结时可以得到的完全钙钛矿相。

In this method, the decomposition of BaCO-3, which is the major reaction rate limiting step in the conventional solid state reaction process, is excluded and so the sintering temperature and holding time required for the completion of the reaction decrease.

本方法不包括传统反应法中限制反应速率的BaCO3分解反应，因而与传统固态反应法相比，其合成温度及保温时间大大降低，从而可以合成超细粉末。

Structural States 、 Sintering Temperature and Thermal Expansion of Cordierite

堇青石的结构状态与合成温度、热膨胀的关系

Effect of Temperature and Atmosphere on Sintering State of Honeycomb Segment Powder

温度和气氛对蜂窝篦齿粉末烧结状态的影响研究

The result shows that the ball's sintering temperature decrease, sintering temperature range enlarge with the pressure increase;

结果表明：在本研究系统内随着压力的增加瓷球的烧结温度下降，烧成温度范围拓宽。

With increasing sintering temperature, the joint of graphite and BN was increased and also there was transition layer in the interfaces relative to HP.

随着烧结温度的升高，元素扩散加剧，过渡层的厚度越厚，材料的层间界面结合强度升高，石墨层与BN层结合的越好。

The Workmanship of Thermal Spray Coating Medium Temperature Reactive Sintering

热喷涂层的中温反应烧结工艺

Improving sintering temperature is conducive to the blue emission. Annealing makes UV emission peak of the film happen blue-shift and blue-ray emission peak happen red-shift.

提高灼烧温度有利于提高薄膜样品的蓝光发射，退火使薄膜的紫外发光峰发生蓝移，蓝光发光峰发生红移。

The sintering temperature and thermal expansion coefficient of the LSGM sample were determined using dilatometer.

用热膨胀仪确定了LSGM的烧结温度及热膨胀系数。

In this paper, side-plate temperature is measured continuously, and software system of thermal state model in sintering process is developed.

本研究通过连续测量烧结机台车侧板温度，开发烧结过程热状态模型系统软件，对烧结过程热状态进行实时判断与分析，在线指导烧结生产，具有重要的理论意义和实用价值。

At high temperature uses are: sintering, welding, hardening, sintering, tempering, Xu cold.

在高温下使用用途有: 烧结 、 焊接 、 淬火 、 烧成 、 回火 、 徐冷.

The sintering temperature of 3 Y-TZP powders can be decreased significantly by the addition of glass powder.

在3Y-TZP粉料中直接加入玻璃粉,可显著降低材料的烧结温度.